Seresto is a flea and tick collar for cats and dogs. It provides a long-term, effective protection from fleas and ticks for up to 8 months. In order for Seresto to work correctly, it needs to fit properly around the neck of your pet – so it is important to ensure that it is correctly fitted.
The process of loosening a Seresto collar can be done quickly but may require some practice. Here are the steps you need to follow:
1. Ensure that your pet’s hair is not obstructing any part of the collar.
2. Unbuckle the collar, then pull apart each side (there will be two halves of the buckle with two metal tabs).
3. Pull on both halves simultaneously away from each other in opposite directions until there is enough slack in the collar (generally when you have about two fingers width between them).
4. Re-buckle the collar again using the same tabs that were pulled apart before, taking care to make sure it is fitted snugly but not too tight around your pet’s neck anymore than necessary for comfort or safety reasons.
5. Check periodically you can slip 2 fingers underneath both sides of the collar evenly at all points where it meets your pet’s neck; this should guarantee that it won’t get too tight if your pet’s fur grows back or if she has lost/gained weight since putting it on
If at any point during the seresto-collar.com adjustment process you are finding that there does not appear to be enough flexibility in Seresto, then check if there are any areas where dirt or excess product have built up blocking movement of parts of the collar – these should be removed safely before proceeding further!
Measure Your Dog’s Neck
Before fitting your dog with a Seresto collar, you’ll need to measure your dog’s neck for proper fitting. It is important to take an accurate measurement to ensure a secure fit of the collar. Measuring your pet’s neck correctly will also help avoid any irritation caused by a too-tight or too-loose fit.
To measure your dog’s neck, grab the measuring tape snugly and place it around the widest part of their neck. Make sure the tape is flat against their fur and hold it in place with steady pressure. Record this measurement either in inches (extend the tape between 8″ and 12″ suggested fitting size) or centimeters. Once you have taken this measurement, you can use it to determine what size Seresto collar you should purchase for your pet.
Put On the Loose Parts of the Collar
The key to properly loosening the Seresto collar is to put on only the loose parts of the collar. This means that you should leave some room for adjusting the fit of the collar on your pet’s neck. To put on the loose parts, start at one end of the collar and slide it over your pet’s head. Make sure not to pull too hard.
Once all of the loose parts are in place, use your finger and thumb to gently press against either side of each prong clip and move it into an open position. Be sure not to pinch any skin or fur while doing this. Then, adjust each prong as necessary so that they can pinch just below your pet’s ear when closed, ensuring a snug but comfortable fit. Finally, close each clip firmly and make sure it clicks in place before testing it by pulling on both ends of the collar with slight tension.
Pull Tightly on Both Ends of the Hook Closure
One of the easiest and safest ways to loosen a Seresto collar is by pulling tightly on both ends of the hook closure. This will add some slack to the collar, which can be helpful if your pet’s neck has grown since you last adjusted their collar. Be sure to take it slow and not pull too hard in order to avoid causing any damage to the collar or buckles.
When you’ve pulled the collar tight enough, simply press the small, white button at the bottom of the buckle, which will release tension on both ends of the collar and create more flexibility. You’ll want to repeat this process until you have a suitable amount of slack in your pet’s Seresto collar – enough space so that you can fit two fingers between their neck and the fabric.
Test For Sufficient Tightness to Keep Fleas & Ticks Out
When loosening your Seresto flea and tick collar, it is important to know that the collar needs to be adequately tight in order to be effective against fleas and ticks. The important thing to remember is that if you have a pet with long hair, there will be more space between the collar and their skin for any pests to get in. To prevent this, you should check the collar is tight enough to fit snugly on your pet’s neck. You can do this by inserting two fingers below the collar and test for sufficient tightness.
If the space between the collar and your pet’s neck is less than one finger’s width, then the ideal amount of snugness has been maintained. Also make sure that when testing for tightness, it’s not so tight as to cause discomfort or choking. If you want an extra safety precaution, double-check with a second person at home who can give further advice if necessary.
Putting all together
Once you have properly fitted your dog’s Seresto collar for flea and tick prevention, use it as directed for ongoing protection against parasites.
Leave a Reply